Bosch Me711 Pinout |work| Review

An interesting technical feature of the Bosch ME7.1.1 pinout is its support for Boot Mode, which allows for a full low-level recovery or "cloning" of the ECU by grounding a specific internal pin during power-up. Key Highlight: The "Boot Pin" Trick

| Pin | Function | Signal Type | Notes / Voltage | | :--- | :--- | :--- | :--- | | 1 | MAF Signal (G70) | Analog Input | 0-5V (idle ~1.5V) | | 2 | IAT (G42) – Intake Air Temp | Analog Input | NTC sensor (shared ground) | | 4 | Lambda 1 (G39) – Pre-cat O2 | Analog Input | 0-1V (narrowband) or 0-5V (wideband LSU 4.2) | | 5 | Lambda 1 Heater Ground | Power Ground | Heater circuit return | | 10 | ECT (G62) – Coolant Temp | Analog Input | NTC sensor (Shared with gauge) | | 15 | CAN Low (Drive train) | Digital | 2.5V nominal, differential (to cluster/ABS) | | 16 | CAN High (Drive train) | Digital | 2.5V nominal, differential | | 19 | Knock Sensor 1 (G61) | AC Signal | Shielded wire | | 20 | Knock Sensor 2 (G66) | AC Signal | Shielded wire | | 24 | MAP Sensor Signal | Analog Input | Manifold pressure (0-5V) | | 27 | Power Supply (Constant 12V) | Power | Direct from battery (Terminal 30) | | 28 | Power Supply (Constant 12V) | Power | Direct from battery (Terminal 30) | | 29 | Power Supply (Constant 12V) | Power | Direct from battery (Terminal 30) | | 30 | Main Relay Control (Terminal 87) | Output | Switched +12V to relay coil (ground side switched) | | 31 | Injector Cylinder 1 (N30) | Output | Ground-switched peak & hold | | 32 | Injector Cylinder 2 (N31) | Output | Ground-switched | | 33 | Injector Cylinder 3 (N32) | Output | Ground-switched | | 34 | Injector Cylinder 4 (N33) | Output | Ground-switched | | 35 | Ignition Coil Output 1 (N70) | Digital Output | 5V logic to integrated igniter | | 36 | Ignition Coil Output 2 (N127) | Digital Output | 5V logic | | 37 | Ignition Coil Output 3 (N291) | Digital Output | 5V logic | | 38 | Ignition Coil Output 4 (N292) | Digital Output | 5V logic | | 40 | Tachometer (Terminal 1) | Output | Square wave (cluster signal) | | 41 | Sensor Ground (Analog) | Ground | Reference for TPS, MAP, MAF | | 42 | Sensor Ground (Analog) | Ground | Dedicated ground | | 43 | Power Ground (ECU Chassis) | Power Ground | Heavy gauge to engine block | | 44 | Power Ground (ECU Chassis) | Power Ground | Heavy gauge | | 45 | Power Ground (ECU Chassis) | Power Ground | Heavy gauge | | 49 | O2 Heater Control (Lambda 1) | PWM Output | Ground-side switch for heater | | 50 | N80 – EVAP Canister Valve | PWM Output | Solenoid control | | 51 | Brake Light Switch (Signal) | Digital Input | +12V when brake pressed | | 55 | Fuel Pump Relay Control (Terminal 87F) | Output | Ground-switched relay coil | | 57 | Clutch Pedal Switch (For cruise) | Digital Input | +12V when engaged | | 62 | Throttle Position Sensor (G79) – Signal 1 | Analog Input | 0.5V – 4.5V (closed-open) | | 63 | Throttle Position Sensor (G185) – Signal 2 | Analog Input | Inverse of G79 (4.5V – 0.5V) | | 64 | Accelerator Pedal (G79) – Signal 1 | Analog Input | Driver demand (0.5V – 4.5V) | | 65 | Accelerator Pedal (G185) – Signal 2 | Analog Input | Inverse of pedal 1 | | 68 | +5V Sensor Supply | Power | To TPS, MAP, pedal sensors | | 71 | +5V Sensor Supply | Power | To TPS, MAP (secondary rail) | | 73 | Camshaft Position Sensor (G40) | Hall Effect Input | 0-5V square wave | | 76 | Starter Signal (Terminal 50) | Digital Input | +12V during cranking | | 77 | Speed Signal (VSS) | Digital Input | From ABS or cluster (CAN also used) | | 78 | Engine Speed (G28) – Crank Sensor | Variable Reluctance | AC sine wave (2 wires – pin 78 & 79) | | 79 | Engine Speed (G28) – Ground/Shield | Ground | Ground for crank sensor shield | | 80 | Ignition Switch (Terminal 15) | Digital Input | +12V when key on | | 92 | Alternator Excitation (DFM) | Digital Input | Monitors alternator load | | 94 | A/C Compressor Request | Digital Input | From HVAC unit | | 95 | A/C Compressor Control | Output | To compressor relay (ground switch) | | 103 | Secondary Air Injection (SAI) Relay | Output | Ground-switched relay | | 105 | Radiator Fan (Low Speed) | Output | To fan control module | | 106 | Radiator Fan (High Speed) | Output | To fan control module | | 108 | OBD-II Diagnostic K-Line (ISO 9141) | Bi-directional | 0-12V (Legacy diagnostics) | | 121 | Main Power Ground | Power Ground | Final high-current ground return | bosch me711 pinout

Boot Pin (POL4): Typically requires a direct connection (often using a resistor like An interesting technical feature of the Bosch ME7

The primary utility of the pinout lies in diagnostics and the critical distinction between inputs and outputs. The ME7.1 is responsible for processing data from a vast array of sensors, including the MAF (Mass Air Flow), crankshaft and camshaft position sensors, and wide-band Lambda oxygen sensors. The pinout identifies exactly which pins receive these signals. For a technician diagnosing a "Check Engine" light, this is invaluable. For instance, if a vehicle displays a code for a faulty throttle body, the technician does not need to replace the entire unit blindly. Instead, they can consult the pinout, locate the specific pins for the throttle motor power and the potentiometer feedback, and use a multimeter or oscilloscope to determine if the signal is reaching the ECU. This shifts the repair process from guessing to scientific verification. Ground: Pin 1 (main power ground) and Pin

  1. Ground: Pin 1 (main power ground) and Pin 77 (sensor ground) – tie both to battery negative.
  2. Constant 12V: Pin T2 and T3 (usually two thick red/black wires).
  3. Switched 12V: Pin 62 (black/violet).
  4. K-Line (for OBD flash): Pin 104 to your interface.
  5. CAN (for some boot mode operations): Pin T6 (CAN-H) and T5 (CAN-L) – optional unless doing CAN-based flashing.
  6. Boot pin (for recovery): For ME7.1.1, you often need to pull a specific pin to ground during power-on to enter boot mode. That pin is Pin 89 (IAT sensor line) – grounding it during the first 100ms of power prevents the main CPU from booting, forcing bootstrap loader mode.

Conclusion

The Bosch ME7.1.1 pinout is a roadmap to the brain of one of the most tunable turbo engines ever made—the VW/Audi 1.8T. Whether you are chasing a no-start, building a swap harness, or bench-flashing a custom tune, the 88 pins of this ECU can be mastered with the table and notes above.

| Pin Number | Pin Name | Description | | --- | --- | --- | | 30 | INJ1 | Fuel injector 1 output | | 32 | INJ2 | Fuel injector 2 output | | 35 | IGN1 | Ignition coil 1 output | | 40 | RELAY | Relay output |